ATTO Technology FC-3321 Setup Guide

aImportant InformationAvid® recommends that you read all the information in these upgrade notes thoroughly before installing or using any new software

Version 3.3 Upgrade Notes10 7. A Question dialog box opens informing you an older version of the LANserver software was detected and must be removed

Upgrading the LANserver113. Make sure the “Enable network sharing on mounted MediaNetwork workspaces” option is selected.4. Deselect “Encrypt data tra

Version 3.3 Upgrade Notes12 Upgrading the Alacritech Ethernet Adapter Board DriverThe Alacritech® driver requires a special procedure to install the

Upgrading the LANserver135. Click Exit to close the Avid Unity Installation window.6. On the MediaNetwork CD-ROM, navigate to:\Drivers_Firmware\Networ

Version 3.3 Upgrade Notes14 After you have determined the type of ATTO Fibre Channel adapter board you have, do one of the following:t If you have an

Upgrading the LANserver158. Click Next. The Choose Install Folder window opens.9. Click Next, or change install path and click Next. The Pre-Installat

Version 3.3 Upgrade Notes16 10. Click Next in Install Hardware Device Drivers Window.11. Click Have Disk in Select a Device Driver Window.12. Click B

Upgrading the LANserver171. Insert the MediaNetwork CD-ROM into the LANserver EX CD-ROM drive. The MediaNetwork v3.3 Installation window opens after a

Version 3.3 Upgrade Notes18 22. Click Next. An Update Driver Warning appears.23. Click Yes. The Start Device Driver Installation screen appears.24. C

Upgrading Windows 2000 Clients198. When the flash completes, click OK and quit the Configuration Utility.9. Reboot the Windows client for changes to t

Version 3.3 Upgrade Notes2 You can perform any hardware changes after the software upgrade is complete and you are sure the new MediaNetwork software

Version 3.3 Upgrade Notes20 5. Click LANshare Components. The screen changes to show the available LANshare component installers.6. Click Install Eth

Upgrading Windows 2000 Clients21Figure 4 Ethernet-Attached Client Connection Configuration10. Select the preferred method of connection:t For a pooled

Version 3.3 Upgrade Notes22 Upgrading the Alacritech DriverThe Alacritech driver requires a special procedure to upgrade correctly for use in a Media

Upgrading Windows 2000 Clients234. Click Exit to close the Avid Unity Installation window.5. On the MediaNetwork CD-ROM, navigate to:\Drivers_Firmware

Version 3.3 Upgrade Notes24 6. Click the Link Speed & Duplex pop-up menu, and select 1000Mb/FullDuplex.7. Click OK to close the Alacritech Accele

Upgrading Windows 2000 Clients255. Click Install Fibre Attached Client. The InstallShield Wizard Minimum Requirements screen appears. Do one of the fo

Version 3.3 Upgrade Notes26 3. On the InstallShield Wizard Complete screen, select the “Yes, I want to restart my computer now” option.4. Click Finis

Upgrading Windows 2000 Clients27Upgrading the Emulex Fibre Channel DriverIf your Windows Fibre Channel client has an Emulex Fibre Channel adapter boar

Version 3.3 Upgrade Notes28 17. Click the Look In pop-up menu, and select CD-ROM.18. On the MediaNetwork CD-ROM, navigate to:\Drivers_Firmware\HostBu

Upgrading Windows 2000 Clients29To install the Emulex SimulateDevice driver for Windows 2000 clients:1. Log in as Administrator.2. Insert the MediaNet

Symbols and Conventions3Installing the Emulex SimulateDevice Driver. . . . . . . . . . . . . . . 28Installing the ATTO Configuration Utility . . . .

Version 3.3 Upgrade Notes30 Installing the ATTO Configuration UtilityThe ATTO Configuration Utility allows you to:• Upgrade the firmware on the ATTO

Upgrading Windows 2000 Clients31Upgrading the ATTO Phantom DeviceThe ATTO Phantom Device will only load when the ATTO Fibre Channel adapter board cann

Version 3.3 Upgrade Notes32 14. Click Open in the Locate File Window. You will receive an incorrect list of devices in the Select a Device Driver Win

Upgrading Windows 2000 Clients335. In the left pane of the window, click Device Manager. A list of devices appears in the right pane of the window.6.

Version 3.3 Upgrade Notes34 26. Click Next. It takes several minutes to install the driver. This time varies based on the Avid workstation. When fini

Upgrading Windows 2000 Clients35Setting Up International Character SupportTo set up a Windows 2000 client for international character support:1. Click

Version 3.3 Upgrade Notes36 4. Double-click ACPI Uniprocessor PC.5. Click the Driver tab.6. Click the Update Driver button. The Update Device Driver

Upgrading Macintosh Clients37To upgrade your LANshare Macintosh clients do one of the following:t If you have Macintosh Ethernet clients attached to a

Version 3.3 Upgrade Notes38 To install MediaNetwork v3.3 software:1. Select Easy Install from the pop-up menu on the Avid MediaNetwork Install window

Upgrading Macintosh Clients398. Click Uninstall. The message “No other applications can be running during this operation” appears.9. Click Continue. A

Version 3.3 Upgrade Notes4 cA caution means that a specific action you take could cause harm to your computer or cause you to lose data.> This symb

Version 3.3 Upgrade Notes40 Mac OS 9 ClientsThe following sections describe how to upgrade firmware, drivers, and hotfixes for the Mac OS 9 operating

Upgrading Macintosh Clients416. Double-click the JNI folder. The JNI window opens.7. Click the Avid Fibre Driver extension and drag it to the System F

Version 3.3 Upgrade Notes42 cDo not stop the Macintosh after beginning the update.8. When the update is finished, close the EPCI FC 33xx Updater 2.3.

Upgrading Macintosh Clients437. Click the Download button. The software downloads to your Macintosh HD drive.8. Double-click the downloaded file to un

Version 3.3 Upgrade Notes44 11. Click OK. The software updates install. A progress bar at the bottom of the Software Update window shows the installa

Upgrading Macintosh Clients458. Read the license and select “I accept the terms of the License Agreement.”9. Click Next. The Important Information – R

Version 3.3 Upgrade Notes46 8. Read the license and Select “I accept the terms of the License Agreement.”9. Click Next. The Pre-Install Summary scree

Upgrading Macintosh Clients479. Double-click FlashBundle_232.2300. The file name and version number appear in the Flash Update File Information sectio

Version 3.3 Upgrade Notes48 To add your language’s keyboard layouts and character set to the operating system’s Input menu:1. Click the Input Menu ta

If You Need Help49The Get Info dialog box makes use of files known as language resource files to specify the language and regional code to use. The Av

Preparing for the Upgrade5Preparing for the UpgradeBefore you begin to upgrade your LANshare workgroup, you need to prepare the clients and LANserver

Version 3.3 Upgrade Notes50 Technical Support InformationMost products feature a number of coverage options. Avid Assurance service offerings are des

Copyright and Disclaimer51Copyright and DisclaimerProduct specifications are subject to change without notice and do not represent a commitment on the

make manage move | media™ Avid®Version 3.3 Upgrade Notes520578801A_UP.fm Page 52 Tuesday, May 6, 2003 4:47 PM

Version 3.3 Upgrade Notes6 nIf you are upgrading from MediaNetwork v3.2, you can skip this section and continue with “Upgrading the LANserver” on page

Upgrading for International Character Support7When you upgrade your LANserver to MediaNetwork v3.3, by default the file system metadata translates all

Version 3.3 Upgrade Notes8 nYou can use whatever method is appropriate for your Windows or Macintosh client to rename these folders or files, changing

Upgrading the LANserver95. Click Review and install updates at the top of the list. The Total Selected Updates page appears. It should contain only Wi