ATTO Technology 1190E Specifications

ATTO Technology, Inc.AT TOTM FibreBridgeTM 1190EInstallation and Operation Manual© 2001 ATTO Technology, Inc. All rights reserved. All brand or produc

5 ATTO Technology FibreBridge 1190E Installation and Operation Manual3 ATTO FibreBridge 1190E characteristicsThe ATTO FibreBridgeTM 1190E is a 1 x 2 (

6FibreBridge 1190EEthernet portThe 10/100 Base T Ethernet port supports SNMP- and Telnet-based monitoring and management through a command line inte

7 ATTO Technology FibreBridge 1190E Installation and Operation Manual4 How to connect SCSI devices to SCSI portsATTO FibreBridgeTM SCSI ports are used

85 How to connect the Fibre Channel portThe Fibre Channel port(s) on the ATTO FibreBridgeTM connect the bridge into either a Fabric or Arbitrated Loop

9 ATTO Technology FibreBridge 1190E Installation and Operation Manual6 ATTO FibreBridge addressingThe ATTO FibreBridgeTM allows parallel SCSI devices

10ATTO FibreBridge addressingFibreBridge. The FibreBridge SCSI ports must be set to different SCSI IDs than the devices on the bus. SCSI devices are

11 ATTO Technology FibreBridge 1190E Installation and Operation Manual7 How to access ATTO FibreBridge ServicesCommunicate with the ATTO FibreBridgeTM

12Access methodsTo connect via Telnet:1 Supply the IP address to the Telnet program. The local echo should be set to on if the Telnet software suppo

13 ATTO Technology FibreBridge 1190E Installation and Operation Manual7.1 Command Line Interface use and guidanceConfiguration of the ATTO FibreBridg

14Command Line InterfaceExhibit 7.1-2 Command conventions.Exhibit 7.1-3 POST informationSymbol Indicates[ ] Required entry< > Optional en

15 ATTO Technology FibreBridge 1190E Installation and Operation Manual 7.1.1 General use commandsThe CLI commands outlined in this chapter get informa

167.1.2 Mapping commandsAccess to SCSI devices is via Fibre Port and Fibre LUN addresses mapped to SCSI bus, target and LUNs. The factory default mapp

17 ATTO Technology FibreBridge 1190E Installation and Operation ManualFcHardUsed to enable or disable Fibre Channel hard address assignment. Under sof

18Mapping commandsRouteOfflineSets a route to offline or reports its status as offline or going offlineAction: set RouteOffline [fp] [fl]Information

19 ATTO Technology FibreBridge 1190E Installation and Operation Manual7.1.3 Diagnostic commandsATTO FibreBridgeTM diagnostic commands help validate Fi

20Diagnostic commandsErrorLogSet form clears ErrorLog since previous error reported. Get form shows error messages since the report was last cleared

21 ATTO Technology FibreBridge 1190E Installation and Operation Manual7.1.4 SCSI configuration commandsThe SCSI ports are configured with default sett

22SCSI configuration commandsScsiPortTaggedQueuingSpecifies whether tagged command queuing is allowed on the SCSI port.Limits: [enabled | disabled]

23 ATTO Technology FibreBridge Installation and Operation Manual7.1.5 Fibre Channel configuration commandsThe Fibre Channel ports are configured with

24Fibre Channel configurationFcInitiatorAllows FibreBridge to operate as an initiator on the Fibre Channel network, an attribute required for featur

Table of ContentsChapter 1 Fibre Channel is a key technology for storage ...1Chapter 2 ATTO FibreBridge supports diver

25 ATTO Technology FibreBridge Installation and Operation Manual7.1.6 Serial Port configuration commandsThe ATTO FibreBridgeTM serial ports are config

267.1.7 Ethernet configuration commandsThe ethernet configuration commands configure the Ethernet and TCP/IP parameters for FibreBridge models with

27 ATTO Technology FibreBridge Installation and Operation Manual7.1.8 Maintenance commandsThe CLI commands outlined in this chapter may be used to get

28Maintenance commandsZmodemAllows transfer of a firmware image to or from the FibreBridge using the ZMODEM file transfer protocol. Limits: availabl

29 ATTO Technology FibreBridge 1190E Installation and Operation Manual7.2 In-band CLI using SCSI over Fibre Channel portIn-band Command Line Interface

30In-band CLI ➔Characters following the NULL character are meaningless.A CHECK_CONDITION, INVALID_PARAMETER_IN_CDB will be returned to an initiator

31 ATTO Technology FibreBridge 1190E Installation and Operation Manual8 Serverless backup supportServerless Backup is an application that allows data

32Serverless backupTo enable serverless backup on the FibreBridge: 1 Access the FibreBridge either through RS-232 or Ethernet.2 After the Ready prom

33 ATTO Technology FibreBridge 1190E Installation and Operation Manual9 Updating firmwareThe ATTO FibreBridgeTM has several processors which control t

iIndex: Command Line Interface commandsAutoMap ... 16ClearEvent ...19DispEvent ...

Chapter 7.1.3 Diagnostic commands ...19ClearEventDispEventDisplayEventEccLogErrorLogIdentifyFibreBr

ii ATTO Technology FibreBridge 1190E Installation and Operation ManualAppendix A Examples of command usageRouteXxxxx commandsThe RouteXxxxx commands a

iiiAppendix A 0 1 0 3 1 Online 0 2 2 0 0 Online 0 3 3 0 0 Online 0 4 xx xx xx 4500 0 5 xx xx xx Offline 0 6 xx xx xx Offline..

iv ATTO Technology FibreBridge 1190E Installation and Operation ManualAutoMap Command SequencesThe following are examples of typical command sequences

vAppendix AReady.RouteDisplay online 17;fp fl sb st sl On/Offline 0 0 0 0 0 Online 0 1 1 4 0 Online 0 2 2 2 0 Online 0 3 xx xx xx 4

vi ATTO Technology FibreBridge 1190E Installation and Operation ManualAppendix B Standards and compliancesThe equipment described in this manual gener

viiAppendix BEuropean StandardsDeclaration of ConformityThis following statement applies to the ATTO FibreBridge. This device has been tested in the

viii ATTO Technology FibreBridge 1190E Installation and Operation ManualAppendix C Fibre Channel AccessoriesThe following Fibre Channel accessories ar

ix ATTO Technology FibreBridge 1190E Installation and Operation ManualField Replacement Units (FRU)PWRA-0000-FRU Power Module for ATTO FC Rack SystemF

x ATTO Technology FibreBridge 1190E Installation and Operation ManualAppendix D How to Contact ATTO Technology, Inc. Customer service, sales informati

Chapter 7.1.8 Maintenance commands ...27FibreBridgeModelFirmwareRestartSerialNumberMaxEnclTempAlrmMinEn

1 ATTO Technology FibreBridge 1190E Installation and Operation Manual1 Fibre Channel is a key technology for storageFibre Channel is a serial communic

2GlossaryF_port A port in the Fibre Channel fabric where a N_port may attachFL-port A port in the Fibre Channel fabric where a NL_port may attach in

3 ATTO Technology FibreBridge 1190E Installation and Operation Manual2 ATTO FibreBridge supports diverse SAN needsThe ATTO FibreBridgeTM family of pro

4IntroductionExhibit 2-1 The following chart provides an overview of the features and capabilities for the newest FibreBridge models. Contact your a