ATTO Technology 2390 Setup Guide

Autodesk® Visual Eects, Finishing, and Color GradingHP® xw8600 WorkstationHardware Setup Guide

7 Perform the procedures in the Autodesk Visual Effects and Finishing Software Installation Guide, AutodeskLustre Software Installation Guide for Wind

Typical Configuration Overview for Autodesk LustreThe following illustration shows a typical configuration, including the Lustre Master Station, Stati

Hardware Configuration GuidelinesIn most cases, hardware integration and application installation are done on delivery by an authorizedtechnician, and

NOTE These values can fluctuate if uncertified hardware components or third party applications are added toyour system. The use of uncertified hardwar

Avoiding Damage from Static ElectricityWhen installing any hardware equipment, take the following precautions to prevent damage to sensitivecomponents

3 Go to the DKU_<version_number>/Utils/BIOS directory on the DVD, where <version_number>represents the version of the DKU. For example:cd

ValueItemBIOS MenuDisableOS Power Management, Runtime Power ManagementPowerNormalOS Power Management, Idle Power SavingDisableOS Power Management, AC

Card #: 0Board Version String: OEM 2K - Rev 0PCI Version: 0x73Board ID: 10196500FPGA built on 2007/09/18 at 10:57:41NOTE If there is no aja file in /p

7 Shut down your workstation by typing:shutdown -g0If your workstation does not prompt you to power down, press the power button for 10 seconds toforc

Connecting PeripheralsTopics in this chapter: Workflow for Connecting Peripherals on page 13 Connecting the Monitor on page 14 Connecting the Keyboard

© 2009 Autodesk, Inc. All rights reserved. Except as otherwise permitted by Autodesk, Inc., this publication, orparts thereof, may not be reproduced i

HP xw8600 WorkstationHD-SDI In (A) from 4:2:2 VTR (or 4:4:4 dual link)HD-SDI In (B) from 4:4:4 VTR (dual link 0:2:2)HD-SDI Out (A) to 4:2:2 VTR (or 4:

The Wacom® Intuos USB tablet is shipped with your system. All customization with respect to the tablet,including setting tablet margins, should be don

4-Port Broadcom AdapterIf you are using Lustre, connect the ports on the Broadcom card as follows: Connect Port 0 to the Autodesk Control Surface hub

NOTE Lustre with Incinerator doesn’t need local storage and uses InfiniBand to connect Incinerator.Connecting and Configuring the ATTO Fibre Channel A

device, as well as to select a text label that identifies the device in the Archiving module. Refer to the AutodeskVisual Effects and Finishing Config

1 3 4 5 6 7 8PWRNETGEAR2Autodesk Control Surface5V DC 4A EthernetAutodeskTabletSystemPowerLinkActivit y-+Network SwitchTo USB extenderPorts 3 and 4 to

5V DC 4A EthernetAutodeskTabletSystemPowerLinkActivity-+To USB extenderAutodesk Control SurfaceTo port 1 on USB Extender3 If you are using more than o

3 In the Local Area Connections Properties dialog box, select Internet Protocol (TCP/IP) and click Properties.The Internet Protocol (TCP/IP) Propertie

nedit /etc/sysconfig/network-scripts/ifcfg-eth<port#>2 Modify the IPADDR and NETMASK values. For example:IPADDR=192.168.125.10NETMASK=255.255.25

Port 1HP xw8600 WorkstationSlave Render Station (HP DL 140 G3)Connecting the Slave Renderer to a Lustre Workstation | 23

DisclaimerTHIS PUBLICATION AND THE INFORMATION CONTAINED HEREIN IS MADE AVAILABLE BY AUTODESK, INC. “AS IS.” AUTODESK, INC. DISCLAIMSALL WARRANTIES, E

24

Setting Up Video HardwareTopics in this chapter: Video Hardware Components on page 25 Wiring Your Video Components on page 26 Setting Up VTR Emulation

Wiring Your Video ComponentsRefer to the wiring diagrams in this section to connect the video I/O components to an HP xw8600workstation equipped with

cnyS neGcnyS neGRef LoopRS-422SDI 1/A SDI 2/BInOutCh.1(L) Ch.2(R)Y/G/CVBS Pb/B/Y Pr/R/CVideo MonitorOutCh. 1/2 Ch. 3/4InOutCh. 5/6InOutInOutCh. 1/2 Ou

162738495162738495WHTBLKBLKREDGNDOEM-2K: MALE DB9OEM-LH: FEMALE DB9MALE DB92 - RX -7 - RX +3 - TX -8 - TX +2 - TX -7 - TX +3 - RX -8 - RX +4 - GND (SH

If you intend to use the emulator as a Player, it is recommended that you connect an external AES signalsuch as a tone to the input of the system serv

WHTBLKBLKREDGNDMALE DB92 -RX -7 -RX +8 -TX -3 -TX+8 -TX -3 -TX +2 -RX -7 -RX+4 - GND (SHIELD)4 - GND (SHIELD)PAIR 1PAIR 2VTR-Emulation Control Cable:3

Setting Up Audio HardwareTopics in this chapter: About Audio on page 31 Audio Wiring Workflow on page 31 Audio Hardware Components on page 32 Audio Wi

4 Connect your audio hardware devices. To avoid system instability, make sure you connect your audiohardware as illustrated for your configuration. Se

Analog InputsAES/EBU Digital OutputsAnalog Outputs3-41-21-25-67-83-45-67-81234567812345678AES/EBU Digital InputsRS-232ADAT IN 1-8ADAT OUT 1-8WORD CLOC

remotely, you must connect the converter to the serial port of the HP xw8600 workstation. Local controlmeans you adjust converter settings manually, u

Lucid ADA 88192 Converter Settings for Remote ControlYou must configure the following settings to control the converter remotely. Any setting not list

CommentMenu ItemMenuFor digital audio: AES INs --> ADAT OUTsAES INs --> AES OUTsAES INs --> ANALOG OUTExternal AES 1+2 is the recommended set

IndexAair conditioning, requirements 6AJA breakout box 25AJA HD5DA 25AJA OEM-2K board 25archive device, configuring 17archive storage, connecting 17AT

Mmemory requirements 6MidiDevice keyword 36monitor 25calibration 15connecting 14mouse, connecting 14Nnetwork, connecting 15notation conventions 2NVIDI

ContentsChapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting to the InfiniBand (IB) Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Connecting Storage . .

IntroductionTopics in this chapter: About This Guide on page 1 Related Documentation on page 1 Notation Conventions on page 2 Contacting Customer Supp

For a list of all the documentation available, visit http://www.autodesk.com/me-documentation. From this pageyou can access the complete documentation

Getting StartedTopics in this chapter: Workflow for Hardware Setup and Application Installation on page 3 Typical Configuration Overview for Autodesk